1,255 pages: the largest collection of information about archery and bowhunting on the web
Enhanced Fishing Society Site
Our enhancement program is 90% complete. Our volunteers have added over 800 pages. We now have over 3,000 and 30,000 links to Fresh and Saltwater fishing, guides, rods, reels, lures, recipes, fish and where and how to fish and the boats to fish in.
The Archery Society
1,000+ pages and 15,000 links to archery and bowhunting, hunting guides, archery history, products and services
Recurve Bow Making
These are asymetrical Yumi Bows
Thank you for visiting our site. We are all volunteers. Recurve Bow Making is a non profit, public service organization. We are devoted to the promotion of archery and bowhunting, the protection of wildlife, and the preservation of wildlife habitats for use by all people.
We try to provide you with the largest and the best collection of information about archery and archery equipment and services available on the net. We update our sources constantly.
We also try to provide information for you in as convenient a manner as possible. Please scroll down to learn more.
Recurve Bow Making
For more information, go to http://www.second-opinions.co.uk/flight-diy-bow.html.
All bows are expensive, which makes archery expensive. But it need not be so. It is possible to make your own Flight bow, either recurve or compound quite cheaply. And it is not as difficult as you might think. Below is an idea for a recurve Flight bow, but a compound Flight bow could also be made in a similar way.
The (easy) homemade Flight bow Flight bows have four components: a pair of limbs, riser which holds them apart, a handle and an overdraw. The shortcut is to let someone else make the limbs, which are the really difficult part, while you make the rest.
A Flight bow is a short bow: overall its length is around 900-950mm (36-371/2") with a riser in the order of 350mm (14"). So the working length of each limb is 275-300mm (11-12").
Method
Beg, borrow or, if you have to, buy a pair of secondhand Target bow limbs or a one-piece recurve Target bow. Make it a cheap secondhand one as you are going to mutilate it. It doesn't matter if the riser is damaged, you won't need it. Next get a piece of seasoned hardwood 350x75x50mm (14x3x2"), finished sizes, for the riser. The riser's 75mm dimension is its width. Cut the limbs off at about 400mm (16"), measured around the recurve, with a band saw or a sharp hacksaw, taking care not to split the fibreglass. It is better to have them slightly too long than slightly too short. Lie the riser wood on its belly on a table. Line up one limb against the side of the riser so that it extends beyond the riser by 300mm (12") at such an angle that the inner end of the limb is in line with the top edge of the riser wood and the bottom of the recurve is touching the table. Mark the side of the riser along the line of the limb. Mark the other end of the riser with a similar line so that the two ends are symmetrical. These wedge-shaped pieces will be cut off.
It is important that the riser is cut accurately where the limbs are to fit. Take the riser blank to a professional woodworker. Ask him to cut off the two wedges accurately and also drill a 38mm (11/2") diameter hole through the centre of the riser from front to back. You will shoot the arrow through this hole.
That is all the wood it is necessary to remove to make the riser, but it will look pretty crude. I will let you decide on the cosmetic treatment.
To fit the limbs requires side plates, or similar, to stop the limbs moving sideways and a bolt through each limb and the riser to bolt them on. (It may be possible to use wood screws into the wood if the poundage is not too high.) Bow weight depends on the weight of the limbs chosen and the amount of prebend when the bow is strung. You will have to experiment here.
Flight bows are much more highly strung than Target bows. Start by stringing to give a bracing height of 100mm (4") using 8 strands of Fastflite (You will probably reduce this to 6 strands in competition). The bow should shoot 15 inch arrows so, with an overdraw back to the string, the draw length needs to be 19" measured from the belly of the bow.
To test, draw the bow mechanically using a spring balance and measure the draw-force curve. The weight divisions are given in the Flight rules. From this basic setup, you can shave the limbs, change the stringing or alter the angle of the limbs on the riser to achieve the weight you want.
Handle
A bow with such a small bracing height is almost impossible to shoot with the usual vertical handle on the riser. The usual Flight handle today is one which is fitted in front of the riser. This not only gets over the problem of hitting your wrist, it also allows the bow to be drawn back to the face. The handle can be mounted either vertical or horizontal. An alternative, and a way that Harry Drake shot, is to turn your bow hand inwards through 180 degrees, as though you were pushing the bow away from you, and using a suitable support on the belly of the bow. This keeps your arm out of the string line without the forward handle. It takes some getting used to.Overdraw
A simple overdraw, which is very effective consists of two strips of metal, one each side of the string, which are fastened to the riser and have vertical saw cuts just in front of the string. The saw cuts hold pieces of 1/16" thick balsa wood into the top of which is a 'v' notch to guide the arrow. This should lie directly in front of the nocking point on the string. The only snag with it is that you will need lots of bits of balsa as you break one each time you shoot.NOTE: This bow may not break records but it is an easy, cheap, fun Flight bow to start with and you should be able to get your Master Flight Shot qualification in Britain with it.
